Stainless steel checker plate is often requested with only a grade and nominal thickness, but that is not enough for a reliable quotation. Buyers should define the base thickness, raised pattern, sheet size, grade, finish, quantity, edge condition, inspection documents and service environment.
For a stainless steel checker plate RFQ, state whether the quoted thickness means the flat base metal or the overall height including the raised pattern. Add the required pattern, grade, width, length, finish, quantity and applicable standard. Weight calculated from flat-sheet density is only a planning estimate because the raised pattern adds material. The final mass, thickness tolerance and slip-performance requirement should be confirmed in the purchase specification.
View Stainless Steel Non-Slip Plate
Stainless steel checker plate is a flat product with raised figures on one surface. It is also described as tread plate, floor plate, diamond plate, chequered plate or non-slip plate. These names are not always interchangeable in a purchase order because suppliers may use different patterns, manufacturing routes and thickness conventions.
The raised pattern can improve traction and help a buyer distinguish the walking face, while stainless steel provides corrosion resistance suited to the selected grade and environment. A patterned surface alone does not guarantee a specific slip rating. Water, oil, cleaning residue, wear, drainage, footwear and installation angle can all change actual performance.
The most common quotation dispute is whether thickness is measured on the flat base or over the raised pattern. The two values are different, and the difference affects weight, fit-up, clearances and price comparison.
| RFQ term | Meaning | Why it matters |
|---|---|---|
| Base thickness | Thickness of the flat plate below the raised figures. | Used for material comparison, fabrication planning and approximate flat-base weight. |
| Pattern height | Height of the raised figure above the base surface. | Affects total profile height, grip geometry and mating clearances. |
| Overall thickness | Maximum thickness measured over the raised pattern. | Important where the plate must fit beneath doors, covers, clamps or existing structures. |
Procurement rule: write “base thickness” or “overall thickness including pattern” directly on the RFQ and drawing. Do not rely on a bare number such as “3 mm checker plate.”
A flat-base estimate can be calculated before the exact raised-pattern allowance is known:
Flat-base weight (kg) = length (m) × width (m) × base thickness (mm) × density (kg/m³) ÷ 1000
For early planning, a density near 8,000 kg/m³ is commonly used for austenitic stainless steel. The purchase calculation should use the agreed grade density and supplier data.
Worked planning example: a 1.219 m × 2.438 m plate with a 3.0 mm base thickness gives approximately 71.3 kg before adding the raised-pattern mass. This is not the final shipping weight. The pattern, dimensional tolerance and actual production route can change the result, so buyers should request the supplier’s theoretical or actual unit weight and state which one controls the commercial calculation.
Common market descriptions include diamond, one-bar, five-bar, lentil, teardrop and other embossed or rolled figures. The same commercial name may refer to different dimensions from different mills. A photograph is helpful, but a drawing or approved sample is safer for repeat orders.
| Selection point | What to specify | Risk if omitted |
|---|---|---|
| Pattern geometry | Name plus drawing, photograph or approved sample. | Different pitch, height or orientation may be supplied. |
| Walking face | Patterned side, installation direction and any drainage requirement. | Installed orientation may not match the design intent. |
| Flatness and edge | Mill edge or cut edge, squareness, flatness and burr limits. | Extra leveling, trimming or deburring may be required. |
| Slip requirement | Project test method, acceptance value and wet/dry or contaminated condition. | A pattern name may be mistaken for verified slip performance. |
304 or 304L is a common starting point for general indoor, architectural and moderately corrosive service. 316 or 316L adds molybdenum and is often considered where chloride exposure, coastal conditions or more aggressive cleaning chemicals are relevant. Grade selection should be based on the actual environment, cleaning method, design life and project specification rather than the assumption that a raised pattern improves corrosion resistance.
For welded fabrication, buyers should also state the required low-carbon grade where applicable, welding procedure, pickling/passivation requirement and whether heat tint must be removed. Carbon-steel tooling contamination should be controlled during cutting and fabrication.
The SAKY STEEL non-slip stainless steel plate page lists ASTM A240 for stainless plate material. Project specifications may also reference general dimensional requirements or a floor-plate standard. The buyer should state the exact standard designation, edition, unit system and any supplementary requirements.
ASTM A240/A240M covers chromium and chromium-nickel stainless steel plate, sheet and strip for general and pressure-vessel applications. ASTM A480/A480M provides general requirements used with several flat-rolled stainless specifications. ASTM A793 is associated with rolled stainless floor plate. These references do not replace the need to define pattern geometry, base thickness, overall height, sheet dimensions and project-specific slip criteria.
Need Stainless Steel Checker Plate for a Project?
Send the grade, base thickness, pattern, sheet size, quantity, finish, standard, inspection documents and delivery destination. SAKY STEEL can review the RFQ and confirm available manufacturing, processing and inspection options.
View Non-Slip Stainless Steel Plate
Send Your Checker Plate RFQ